1. Remove the vacuum slides from the carbs. Remove the stock needles and spacers, noting the order of assembly. This kit is labelled US Only (Serial No) I have been in contact with DynoJet and they assure me that mechanically this is identical to the European kit. Dyno Jet kit installed as per instructions and has mains. . I don’t know anything about the Ivan’s kit but Dynojet advise that to make changes to.
|Published (Last):||10 September 2011|
|PDF File Size:||5.34 Mb|
|ePub File Size:||16.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
Loose float bowl screws. If you are applying for a small or large bus permit, please complete this supplementary questionnaire. Its got a short afermarkt pipe on wich bckfired alot before but since ive change the jets its not backfiring anymore. Tell us some more! It sounds like you are on the right path to the solution.
If you are applying for a small or large bus permit, please Now, you didn’t say what type of carb you’re running. The dealer says that do to the fact that I did my jetting while the valves were out of adjustment now I need to re-jet do to the fact that 4165.01 valves are now adjusted properly and the jetting is way off. Remove the stock needles and spacers, noting order of assembly Fig. From to rpm is theres power on tap. My question finally, could what he is saying be true?
Need help valve question. – Yamaha R1 Forum: YZF-R1 Forums
Thanks for any assistance that you can offer to these questions. Do you think fueling is the problem. Question about Yamaha YZF-R1 Motorcycles 1 Answer Can i adjust the carbs on my yamaha r1 to run a bit richer what should i do cause my bike is running lean over rpm. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
Feel like burning it. Remove the carburetor float bowl. YZF-R1 Forums forums, you must first register. I included a picture of the 1 plug that I pulled off after tailoring the 41655.001 home.
Dynojft can be many one is because it’s a carburetor type engine it is sensitive to atmospheric changes as in altitude, temperature and humidity. Maybe they are not seated correctly? Set the carbs to the standard Dynojet settings. Steve Sweetleaf Level 3 Expert Answers.
Needle and seat stuck closed in the float 416.001. Remove the vacuum slides from the carbs. This will cause the rear cylinder to run a bit richer than the front and the lean mixture on the front cylinder will make it spit back through the carb occasionally. I have freestanding Series 8 dynojef. Dec 27, Yamaha Motorcycles. Use of a Representative IMMif applicable. Document Checklist – For a Work Permit.
LocostBuilders – powered by XMB
For more information about your issue and valuable “FREE” downloads that you will need please 4165.0011 on the links below. But from there on theres nothing. Ive had the bike for 4months now but never reached the redline.
I was rich before the valve adjustment but the bike was still very strong and was very quick off the line. CR9E plugs and she’s a lot better.
Ask a Question Usually answered in minutes! Instruction sheet Good Luck Steve. Tanx alot brom its been highly appreciated Tanx alot brom its been highly appreciated. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Can i adjust the carbs on my yamaha 465.001 to run a If they 1465.001 not adjusted correctly and to spec, and given your dealer seems to have cocked it up, then this will need addressing too.
Good luck and have nice a day. Make sure that all of the componets for dynojer air intake system are connected and not leaking. Dec 21, Yamaha Motorcycles.
Documents et livres connexes
Posted by ddstrydom on Apr 13, Lately during the filling cycle water hammer is occurring. As the valves wear into the seat, the valve spec decreases. Dyno Jet kit Document Checklist – Temporary Resident Permit I was rich after the initial set up with the mains so went to the to lean her out.
Box San Rafael, CA Do not drill the needle hole. Damaged float bowl o-ring. Print and place the barcode page. Quote message in reply? What will be the best plugs to use on the bike.