AS/NZS A1 Structural steel welding – Part 1: Welding of steel structures: Amendment 1. Correction amendment declared by Standards Australia to. AS/NZS Structural steel welding Part 1: Welding of steel structures; AS/NZS Structural steel welding Part 3: Welding. This Standard specifies requirements for the welding of steel structures made up of combinations of steel plate, sheet or sections, including hollow sections and.
|Published (Last):||12 May 2017|
|PDF File Size:||15.45 Mb|
|ePub File Size:||17.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
This is largely due to the ISO based classifications for most processes adopting similar strength, impact resistance and hydrogen control designations. Published on 23 September Click on the red box above to activate the Licence Agreement scroll bar. Instructions for the qualification of welding procedures on steels not listed in Clause 2.
AS/NZS 1554.1:2014 A1 Structural steel welding – Part 1: Welding of steel structures: Amendment 1
Any recommendations of the manufacturer, covering protection during storage and use, aas and pretreatment of electrodes or filler wires prior to use, shall be followed. Licensees are permitted to print once for Internal use limited to the Quantity specified in the SAI Global Infostore order only excludes electronic pads of forms.
The transition shall be made by chamfering the thicker part or by sloping the weld surfaces, or by any combination of these as shown in Figure 3. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us weldijg of any apparent inaccuracies or ambiguities. Alternatively, the weld may be considered to be defective and dealt with in accordance with Clause 6.
All welds shall receive a full visual inspection in accordance with Section 6. Where imperfections in excess of the limits in Table 6.
Welds nominated as Category SP, but stryctures complying with the requirements of that category, may be considered as Category GP welds, provided the requirements of the design Standard are satisfied and the principal has agreed. Guidance as to the extent of non-destructive examination is given in Table 7.
See Appendix D, Item d. See Appendix D, Item v. Please copy and paste this embed script to where you want to embed Embed Script. Electrodes that do not comply with the above Standards may be used, provided they are qualified in accordance with the requirements of Clause 4.
When applying this qualification for single-run and multi-run fillets, consideration shall be given to the pre-heat requirements for combined thicknesses of T1, T2 and T3, and the pre-heat requirements for the combined thicknesses shall be shown on the welding procedure specification WPS and on the procedure qualification record PQR. Mr Vijai Moorthy Date: Licence Agreement Legislation; 3.
The minimum centre-to-centre spacing in a longitudinal direction on any line shall be atructures times the length of the slot. Welding power sources IEC This Standard does not apply to the welding of pressure vessels and pressure piping.
Criteria for the selection of the appropriate level of quality requirements Please help us to share our service with your friends. Free shrinkage restricted structure e. The flattening of the section shall be made strutures the minimum length practicable. Single-run and multi-run fillet welds may be qualified on opposite sides of the same test plates.
Some consumables may have classifications that vary from that shown. Get permission to copy from this publication www. Licensed to Mr Vijai Moorthy on 31 March The system A classification though remains consistent with the method used for other consumables types.
AS/NZS – Standards Australia
The following are represented on Committee WD Know when a Standard has changed 3. We need your help to maintenance this website. The extent, type and control of this documentation should be agreed prior to the commencement of the work see Appendix D. Except where a greater hardness is permitted in accordance with Appendix D, Item ithe hardness of weld-heat-affected zones shall be not greater than HV This Standard does not apply to underwater struuctures.
The Licensee isLearn grantedabout a non-exclusive and non-assignable Licence to use the Product.
In all other cases or where equivalence cannot be established, it will be necessary to requalify the weld procedure in accordance with the requirements of this Standard. Where seal welding is required, Clause 3.
The specimen shall comply with Table 4.
Where non-complying welds are detected during a spot examination, two additional spots, each of the same length as the original spot, should be examined. Thank you for interesting in our services. Temporary backing material of any type may be used for welds, provided the finished weld complies with the requirements of this Standard.
The permissible service temperatures listed in Table B1 shall be subject to the limitations and modifications specified in Paragraphs B4. Where the mechanical properties of the transverse butt tensile test meet the minimum requirements shown in Table 4.